How to Install Merlin on a Toshiba 100 CS using
a Panasonic KHL-D740 PCMCIA CD-ROM drive.

Config.sys on diskette 1 must be modified by:

Rem out three lines

           rem basedev=btscsi.add
           rem basedev=fd16-700.add
           rem ibm2scsi.add

*AND* delete the associated driver (needed to make room for new drivers).

A copy of pcmcia.sys must be procured from the Merlin CD-ROM. This is easy for experienced OS/2 users (but less so for newbies).
1. Boot OS/2 to a command prompt (the install floppies allow this by F3 after disc 2).
2. Copy to a scratch sub-directory:
```
                 x:\os2image\disk_3\unpack2.exe
                 x:\os2image\disk_17\pcmciadd
                 x:\os2image\disk_18\pcmcia
```
3. Run the unpack command by:
```
                 unpack2 filename scratch.subdirectory
```
  (unpack2 needs a target, else it fails)
I think unpack2.exe is a bound program, so the directions should work from DOS.

Tosh 100 owners copy IBM2TOS1.sys and PCMCIA.SYS from the scratch.directory to Diskette 1 of the install series. Owners of other laptops should sub- stitute for IBM2TOS1.sys their appropriate driver.

         IBM2SS01.SYS | IBM PS/55E, PS/2E, 4SLOTSCARDforISA,
                      | ThinkPad series except 720
         IBM2SS02.SYS | ThinkPad720
         IBM2AMB1.SYS | Ambra486SN425C
         IBM2AST1.SYS | AST Ascentia800N, TBravo, TPowerExec
         IBM2CAD1.SYS | AustinDSTN, Compuadd425TX
         IBM2CMQ1.SYS | CompaqConcerto
         IBM2MAT1.SYS | DELL Latitude, LatitudeXP, Panasonic
         IBM2NEC1.SYS | NECVersa
         IBM2ZOS1.SYS | Zeos
         IBM2ZEN1.SYS | ZenithZ-lite425L
         IBM2TOS1.SYS | Toshiba T3600, T4500, T4600, T4700, T4800
         IBM2NCR1.SYS | NCRSafari

If your computer's name is not in the list, copy the IBM2TOS1.SYS

Go to the Panasonic site and procure 740OS2.exe (which has directions in broken english :-), run the exe to unzip and copy to diskette 1:
```
		kme4os2.sys
		kme4os2.add
```
Edit config.sys on Diskette 1 so the last four lines are:
```
                  basedev=pcmcia.sys /p
                  basedev=ibm2tos1.sys /s0=2 /c0=15
                  basedev=kme4os2.sys
                  basedev=kme4os2.add
```
I didn't figure out if our PCMCIA modem is important to the ibm2tos1.sys line (PCMCIA in top slot, CD-ROM in bottom slot).

Final diskette1 config.sys is:

buffers=32
iopl=yes
memman=swap,delayswap
protshell=sysinst1.exe
set os2_shell=sysinst2.exe
diskcache=D2,LW
protectonly=yes
libpath=.;\;\os2\dll;\os2\install;
ifs=hpfs.ifs /c:64
pauseonerror=no
codepage=850
devinfo=kbd,us,keyboard.dcp
devinfo=scr,ega,vtbl850.dcp
device=\dos.sys
device=\mouse.sys
set path=\;\os2;\os2\system;\os2\install
set dpath=\;\os2;\os2\system;\os2\install
set keys=on
basedev=ibmkbd.sys
basedev=ibm1flpy.add
basedev=ibm1s506.add
basedev=ibm2flpy.add
basedev=ibm2adsk.add
rem basedev=ibm2scsi.add
basedev=ibmint13.i13
basedev=os2dasd.dmd
device=\testcfg.sys
basedev=xdfloppy.flt
set os2_shell=cdinst.exe
set saveconnect=1
set cdrominst=1
ifs=cdfs.ifs /q
basedev=aha152x.add
basedev=aha154x.add
basedev=aha164x.add
basedev=aha174x.add
basedev=aic7770.add
basedev=aic7870.add
rem basedev=btscsi.add
rem basedev=fd16-700.add
basedev=fd8xx.add
basedev=fd7000ex.add
basedev=dpt20xx.add
basedev=dac960.add
basedev=flashpt.add
basedev=ipsraid.add
basedev=ql10os2.add
basedev=ql40os2.add
basedev=ql510.add
basedev=chincds1.flt
basedev=hitcds1.flt
basedev=neccds1.flt
basedev=sonycds1.flt
basedev=toshcds1.flt
basedev=ibmidecd.flt
basedev=tmv1scsi.add
basedev=sony535.add
basedev=lms206.add
rem 154569 basedev=lms205.add
basedev=mitfx001.add
basedev=sbcd2.add
basedev=sony31a.add
device=\os2cdrom.dmd
set os2_shell=cdboot.exe
set oemprogram=\ibminst\npconfig.exe
set exitwhendone=1
basedev=pcmcia.sys /p
basedev=ibm2tos1.sys /s0=2 /c0=15
basedev=kme4os2.sys
basedev=kme4os2.add

Start the Merlin install using the modified Diskette 1 (0 and 2 haven't been touched). Twin-beeps during boot means the CD is happy. Go through the first phase of the install. Beeps indicate success.
The CD-ROM will be "lost" after the first HD reboot because pcmcia.sys is not in X:\os2\boot as expected for a *.sys file. Allow the boot to the configuration screens, then use the F3 escape to a command line. Copy from diskette 1 PCMCIA.sys to the your boot drive (X:) in X:\OS2\Boot. The config.sys on the HD shouldn't have to be altered as it's pulled from the floppy (it looks weird at this intermediate stage of installation).
Remove the floppy, CAD reboot the system, and let OS/2 boot (meaning choose it on Boot Manager if available). You should end up at the same configuration screen you were for step 3 above (where you did F3 to get a command line). Install should go as expected from here on.
The first GUI set-up screen had a Panansonic LK-MC501 S listed as the CD-ROM and Adaptec 1460.... as the SCSI -- these were left alone. Card services installed (guess) were Toshiba 4800 (seem to work).

The final (hard drive) config.sys is:

IFS=D:\OS2\HPFS.IFS /CACHE:2048 /CRECL:16 /AUTOCHECK:DE
PROTSHELL=D:\OS2\PMSHELL.EXE
SET USER_INI=D:\OS2\OS2.INI
SET SYSTEM_INI=D:\OS2\OS2SYS.INI
SET OS2_SHELL=D:\OS2\CMD.EXE
SET AUTOSTART=PROGRAMS,TASKLIST,FOLDERS,CONNECTIONS,WARPCENTER
SET RUNWORKPLACE=D:\OS2\PMSHELL.EXE
SET COMSPEC=D:\OS2\CMD.EXE
LIBPATH=.;D:\OS2\DLL;D:\IBMI18N\DLL;D:\MPTN\DLL;D:\IBMCOM\DLL;D:\OS2\MDOS;D:\;D:\OS2\APPS\DLL;D:\javaos2\dll;D:\MMOS2\DLL;D:\IBMINST;e:\tcpip\dll;e:\tcpip\pcomos2;E:\TCPIP\UMAIL;
SET PATH=D:\MPTN\BIN;D:\IBMCOM;D:\OS2;D:\OS2\SYSTEM;D:\OS2\MDOS\WINOS2;D:\OS2\INSTALL;D:\;D:\OS2\MDOS;D:\OS2\APPS;D:\javaos2\bin;D:\MMOS2;e:\tcpip\bin;e:\tcpip\pcomos2;E:\TCPIP\UMAIL;e:\util;
SET DPATH=D:\MPTN;D:\IBMCOM;D:\OS2;D:\OS2\SYSTEM;D:\OS2\MDOS\WINOS2;D:\OS2\INSTALL;D:\;D:\OS2\BITMAP;D:\OS2\MDOS;D:\OS2\APPS;D:\MMOS2;D:\MMOS2\INSTALL;D:\IBMINST;E:\TCPIP\PCOMOS2;
SET PROMPT=$i[$p]
SET HELP=D:\MPTN;D:\OS2\HELP;D:\MMOS2\HELP;e:\tcpip\help;E:\TCPIP\UMAIL;
SET GLOSSARY=D:\OS2\HELP\GLOSS;
SET IPF_KEYS=SBCS
PRIORITY_DISK_IOs2.add
basedev=ql40os2.add
basedev=ql510.add
basedev=chincds1.flt
basedev=hitcds1.flt
basedev=neccds1.flt
basedev=sonycds1.flt
basedev=toshcds1.flt
basedev=ibmidecd.flt
basedev=tmv1scsi.add
basedev=sony535.add
basedev=lms206.add
rem 154569 basedev=lms205.add
basedev=mitfx001.add
basedev=sbcd2.add
basedev=sony31a.add
device=\os2cdrom.dmd
set os2_shell=cdboot.exe
set oemprogram=\ibminst\npconfig.exe
set exitwhendone=1
basedev=pcmcia.sys /p
basedev=ibm2tos1.sys /s0=2 /c0=15
basedev=kme4osWPSH.IR;D:\OS2\ETC\WPDSERV

How to Install Merlin on a Toshiba 100 CS using a Panasonic KHL-D740 PCMCIA CD-ROM drive.

How to Install Merlin on a Toshiba 100 CS using
a Panasonic KHL-D740 PCMCIA CD-ROM drive.